Articles September 26, 2026 16 min read

Freestanding Deck Plans: Framing, Footings, Bracing and Sizes

What freestanding deck plans must show: beam lines, footings, bracing, guards and permits, with layouts for common sizes and a real framing plan.

Freestanding deck plans have to answer a question an attached deck never faces: with nothing bolted to the house, what holds the deck up and keeps it from swaying? Maybe your house has brick veneer, the floor cantilevers past the foundation, or the spot you want is an old slab outside a new slider.

A freestanding deck handles all three. It swaps the ledger for a second beam line on its own footings, so nothing drills through your siding. The price is more framing, more footings and bracing the house used to provide.

Quick answer

Freestanding deck plans need two beam lines, a footing under every post, joists sized from the IRC R507 tables and your decking maker’s spacing, and lateral bracing, since nothing ties the deck to the house. Guards start above 30 in. The model code skips the permit only for an unattached deck of 200 sq ft or less, no more than 30 in. above grade, that doesn’t serve the required exit door; Pennsylvania’s UCC and local rules can differ, so check with your township.

Freestanding deck vs. attached to the house

An attached deck hangs one side on a ledger bolted to the house. A freestanding deck replaces the ledger with a second beam line on its own footings and stands on its own, up and down and side to side.

Go freestanding when a ledger is a bad idea or impossible:

  • Brick or stone veneer, which can’t carry a ledger.
  • Cantilevered floors and bump-outs with no solid rim joist.
  • An existing slab, like the sample plan below.
  • Siding and flashing you’d rather not open up.
  • Island decks out in the yard, by a pool or a fire pit.

The trade-offs: an extra beam line and footings, your own bracing, and a gap at the house wall.

FeatureFreestanding deckAttached deck (ledger)
At the houseSecond beam line on its own footings, small gap to the wallLedger bolted and flashed to the rim joist
Holes in the sidingNoneLedger fasteners
Side-to-side stabilityBracing, embedded posts or engineeringHouse connection plus the deck’s bracing
Footing depth (2021 IRC)At least 12 in. below undisturbed ground; frost depth if your town requires itFrost protection required (R507.3.3)
Cost driversExtra beam, footings, bracingSiding work, flashing, fasteners

What freestanding deck plans must show

A sketch with outside dimensions isn’t something a builder or inspector can check. Good freestanding deck plans show the structure from the ground up:

  1. Site plan: house wall, doors, downspouts, setbacks and the gap to the house.
  2. Heights: finished surface against the door threshold, and height above grade at the open edges.
  3. Footings: count, diameter, depth, and what they bear on.
  4. Beams and posts: size, ply, post spacing and cantilevers.
  5. Joists: size, spacing, direction, cantilevers and blocking.
  6. Connectors: post bases, post caps and a tie at every joist.
  7. Bracing: type and location, in both directions.
  8. Stairs and guards: risers, treads and rail height.
  9. Decking: material, pattern and fasteners.
  10. Notes: the code edition, and who confirms spans, footings and connections.

Many building departments also want a cross-section. Our guide to landscape plan drawing covers scale and dimensions, and backyard layout helps you place the deck.

Freestanding deck framing: beams, posts and joists

Freestanding deck framing is ordinary deck framing with one change: the house side gets its own beam. Two beam lines run parallel to the house, one a short distance off the foundation and one near the outer edge, with joists spanning between them.

The inner footings are where freestanding decks most often go wrong. Soil against a basement wall is often loose backfill, and footings must bear on undisturbed soil. Dig through it, or set the beam farther out and cantilever the joists back toward the house within the span table’s limits.

AWC’s DCA 6 deck guide sets a 6×6 minimum post, and builders use it as the common reference even though it’s written for attached decks. IRC Table R507.4 caps post height by size, and R507.4.1 requires a manufactured connector or at least 12 in. of embedment at the post base. Under R507.5, beams may cantilever past an end post up to one-fourth of their actual span, so posts can tuck in from the corners.

Joist sizes come from the span table in R507.6, and spacing is limited by the decking (R507.7). We don’t print span charts on purpose: spans change with species, grade, spacing and snow load.

Freestanding deck framing diagram, plan viewPlan view of a freestanding deck: the house wall at top with a small gap, an inner beam line on its own posts and footings set out of the foundation backfill, joists spanning to an outer beam line and cantilevering past it, and a note to brace both directions at the posts.HOUSE WALL (nothing fastened to it)Foundation backfill: keep footings out of itDeck stops 1–2 in. short of the wallINNER BEAM on its own posts and footingsOUTER BEAM on posts and footingsJOISTS span beam to beam (size from IRC R507.6)Joist cantilever past the outer beam (limited by R507.6)PostFooting on undisturbed soilBeamBrace both directions at the postsmuthlerlandscaping.com · not to scale
Freestanding deck framing diagram (plan view): two beam lines, each on its own posts and footings, with nothing fastened to the house. Member sizes and post spacing come from the IRC R507 tables for your deck. Diagram: muthlerlandscaping.com

Ground-level vs. elevated freestanding decks

Height changes the framing more than size does. A ground-level freestanding deck, like an island deck in the yard or a platform a step off a patio, can sit low enough for the code’s pier-block exception: joists right on precast blocks, 200 sq ft or less, and a walking surface no more than 20 in. above grade within 36 in. of the edge. An elevated freestanding deck at a raised slider or over a walkout is the hard case: taller posts that need bracing both ways, guards once it passes 30 in., and, as a rule of thumb, an engineered bracing design at about 4 ft or more.

Composite decking on a freestanding frame

As a rule of thumb, composite makers allow 16 in. on center for boards square to the joists and call for 12 in. for diagonal layouts, heavy loads or intricate patterns; stair stringers usually go 12 in. or closer. Your product’s install guide wins.

A picture-frame border needs perimeter blocking so every board and miter lands on wood, and a breaker board needs doubled joists or blocking under it. Joist tape keeps water off the joist tops, and hidden fasteners need joists that are flush and in plane.

Footings and frost: what the code says

The 2021 IRC Section R507.3 puts decks on concrete footings or another approved system, with two exceptions for free-standing decks. No footings are required when the joists rest directly on grade over their entire length, or when all three of these are true:

  • The joists bear directly on precast concrete pier blocks at grade, with no beams or posts.
  • The deck is 200 sq ft or less.
  • The walking surface is no more than 20 in. above grade at any point within 36 in. of the edge.

Posts and beams on deck blocks don’t qualify; the joists themselves must sit on the blocks.

For depth, R507.3.2 puts every deck footing at least 12 in. below undisturbed ground, and R507.3.3 requires frost protection, such as going below the frost line, where a deck is attached to a frost-protected structure. The 2018 edition said outright that free-standing decks need not have footings below the frost line. Your town’s adopted edition and amendments decide, so ask before you dig.

12 in.minimum footing depth below undisturbed ground
20 in.max deck height for the pier-block exception
200 sq ftsize cap for pier-block and permit exemptions
30 in.deck height that triggers guards

Rule of thumb: we take freestanding deck footings below frost depth whenever the deck meets a door, carries a roof or stands more than a couple of steps up. An inch of heave at a threshold is a trip edge.

Before any auger touches the ground, contact 811 a few business days ahead. It’s the free national before-you-dig service.

Freestanding deck bracing

An attached deck leans on the house to stay put. A freestanding deck has to resist racking by itself, parallel to the house and away from it, and the plan should show how:

  • Knee braces: diagonals from post to beam, and from post to framing the other way. The usual choice once posts pass about 2 ft.
  • Embedded posts: posts set deep in soil or concrete. The 12 in. of embedment in R507.4.1 restrains the post base; bracing a taller deck this way takes design.
  • Horizontal bracing: diagonals under the joists stiffen the floor frame.
  • Engineered systems: steel, helical piers or special connectors, designed for your deck.

DCA 6 calls for diagonal bracing parallel to the beam at corner posts taller than 2 ft, even on attached decks; a freestanding deck needs the other direction too. As a rule of thumb, one roughly 4 ft or more above grade gets an engineered bracing design. If your yard falls away from the house, our sloped backyard ideas cover when a deck beats a wall.

Mistake to avoid: screwing a freestanding deck to the house to steady it. Once fastened, it’s an attached deck without a proper ledger, flashing or lateral connection.

Freestanding deck framing plan example: 34 × 10 ft composite deck

Sample freestanding deck plans: framing and footing plan for a 34 × 10 ft composite deck with two beam lines on 12 piers
Sample plan 05: freestanding composite deck, 34 × 10 ft, with two beam lines on 12 piers. A real Groundwork plan, client details removed. See all sample plans

This real plan is a 34 × 10 ft (340 sq ft) composite deck off a new slider, about 32 in. high, built freestanding over an existing slab: no ledger, no holes in the siding. Two beam lines of 2-ply 2x10s sit on 6×6 posts at 6 ft 5 in. on center with post bases and caps, on 12 piers 24 in. in diameter and 48 in. deep, with a note to confirm local frost depth. The inner piers are cut through the slab with an isolation joint, and the surface sits 1 in. below the slider threshold, with the door set before framing.

On top, 2×8 joists at 12 in. on center carry the composite decking, with a hurricane tie at every joist and joist tape on every top. A picture-frame border and center breaker board go down with hidden fasteners, a 36 in. aluminum rail runs the open sides, two stairs come down, and the space underneath is storage. Those member sizes suit this deck’s spans; they’re not a recipe for yours, and the plan says so: “Framing is a starting point: your builder and building department confirm spans, footings and connections.” We draw sheets like this through our online deck design service.

Our freestanding deck framing plan page walks through this sheet in full: why the deck went freestanding over an old heaving patio, the piers cut through the slab, and the beams, joists and stairs.

8×8, 12×12, 12×16 and 12×20 freestanding deck plans

These are layouts to expect, not designs. Member sizes and post spacing come from the R507 span tables or your local code.

Deck sizeAreaTypical layoutFootings to expectLow-deck exemptions?
8 × 8 ft64 sq ftTwo 8 ft beam lines, joists spanning between them4, a post near each cornerPossible: under 200 sq ft
12 × 12 ft144 sq ftTwo 12 ft beam lines, posts set in from the corners4 to 6, by beam sizePossible: under 200 sq ft
12 × 16 ft192 sq ftTwo 16 ft beam lines, joists running the 12 ft direction6 to 8Possible: just under 200 sq ft
12 × 20 ft240 sq ftTwo 20 ft beam lines, joists running the 12 ft direction8 or more, by beam sizeNo: over 200 sq ft
34 × 10 ft (sample plan 05)340 sq ftTwo beam lines, posts 6 ft 5 in. on center12 piersNo: over 200 sq ft and 30 in.

Note where 12 × 16 lands: 192 sq ft, just under the 200 sq ft line in both exemptions. Built 20 in. or lower with the joists right on precast pier blocks, it needs no poured footings under the model code; at 30 in. or lower, unattached and away from the required exit door, it needs no permit. Your town may differ.

A 12 × 20 is where many plans cross both lines. At 240 sq ft it falls outside both the pier-block exception and the model code’s permit exemption for small decks, however low it sits, so plan on a permit. Unless the joists rest directly on grade along their full length, plan on footings too, and confirm with your local code office, since towns amend these rules. Our footing calculator estimates depth and concrete for each pier.

Height, guards and stairs

Guards are required where the walking surface is more than 30 in. above grade within 36 in. of the edge. They must be at least 36 in. high, with no opening that passes a 4 in. sphere (IRC R312.1). Rail posts fail at the connection, so block them the way the rail maker specifies.

Stairs (IRC R311.7): risers 7¾ in. max, treads 10 in. min, and no riser more than ⅜ in. taller than the shortest. Pennsylvania’s UCC loosens two of those numbers: risers up to 8¼ in. and treads at least 9 in. (34 Pa. Code § 403.21). Four or more risers need a handrail, 34 to 38 in. high. Say your deck is 32 in. above the landing: 32 ÷ 7¾ = 4.1, so you need five risers of about 6⅜ in., plus a handrail.

Land the stairs on a paver or concrete pad so the bottom riser stays equal. Our hardscape design guide covers the landings and walks that meet a deck.

Builder’s note: set the deck surface just below the door threshold (sample plan 05 uses 1 in.) and install any new door before you frame. Fixing it later means resetting every post.

Do you need a permit for a freestanding deck?

Usually, yes. The 2021 IRC exempts a deck from permits (R105.2) only if it’s 200 sq ft or less, no more than 30 in. above grade at any point, not attached to a dwelling, and doesn’t serve the required exit door. An exemption doesn’t authorize work that breaks the code, so an exempt deck still has to be built right.

Towns can amend that list, and zoning setbacks and HOA rules apply either way. Sample plan 05, at 340 sq ft and about 32 in. high, needs a permit under the model code. Not every state is on the 2021 edition; our building codes by state guide shows which IRC edition yours uses.

Freestanding deck with a roof

A roof turns the deck into a small building: the posts carry roof snow and wind loads to the footings, and the roof catches wind that racks the frame. Design the roof and deck as one structure with your building department. Tall decks, roofs and hot tubs often require an engineer’s design.

Mistakes to avoid when building a freestanding deck

  • Framing before the new door is in, then finding the threshold an inch off.
  • Setting posts and beams on deck blocks and calling it the code’s pier-block exception.
  • Spacing joists at 16 in., then picking a diagonal pattern or a board that calls for 12 in.
  • Skipping bracing because the bare frame feels stiff.
  • Bolting rail posts to a single rim board with no blocking.
  • Landing stairs on lawn that settles and changes the bottom riser.

Common questions about freestanding decks

How far should a freestanding deck be from the house?

Close, but not touching. A gap of an inch or two is common, so the deck never bears on the siding and debris falls through. Keep the inner footings out of foundation backfill, and fasten nothing to the house.

Does a freestanding deck need footings below the frost line?

Under the 2021 IRC, deck footings go at least 12 in. below undisturbed ground, and frost protection is required where a deck is attached to a frost-protected structure. The 2018 edition said free-standing decks need not have footings below the frost line. Your town can require frost depth anyway, and we use it for decks at doors or under roofs.

Can a freestanding deck sit on deck blocks?

Yes, if the joists bear directly on precast concrete pier blocks at grade with no posts or beams, the deck is 200 sq ft or less, and the walking surface is no more than 20 in. above grade within 36 in. of the edge. Blocks can shift with frost, so keep a block-supported deck away from door thresholds.

How do you build a freestanding deck?

Get a plan and permit, call 811, and set any new door first. Lay out both beam lines, pour and inspect the footings, set posts on connectors and beams on caps, then set joists with a tie at every beam crossing. Brace the frame, tape the joist tops, and install decking, rails and stairs to the makers’ instructions.

Is a freestanding deck cheaper than an attached deck?

Usually not. It trades the ledger, flashing and siding work for a second beam line, more footings and bracing. It pays off when a ledger would mean cutting into veneer, working around a cantilevered floor, or building over a slab.

What size freestanding deck can I build without a permit?

Under the 2021 IRC (R105.2), a deck is exempt only if it is 200 sq ft or less, no more than 30 in. above grade at any point, not attached to the house and not serving the required exit door. Towns can amend that, so check with your building department first.

How high can a freestanding deck be?

There is no single number, but height changes the rules: guards above 30 in., diagonal bracing at corner posts over 2 ft per DCA 6, and post heights capped by IRC Table R507.4. As a rule of thumb, we get an engineered bracing design once a freestanding deck is about 4 ft or more above grade.

How do you keep a freestanding deck from swaying?

Brace it in both directions: knee braces from posts to the beams and to the framing the other way, diagonal bracing under the joists, or posts embedded in concrete on a designed system. Never screw it to the house to steady it; that makes it an attached deck without a proper ledger.

Can you build a freestanding deck on a slope?

Yes. Taller posts on the downhill side take up the drop, but that edge sets the rules: guards over 30 in., knee bracing on tall posts, footings on undisturbed soil, and an engineered bracing design once the deck is about 4 ft or more above grade.

Can a freestanding deck be cantilevered?

Yes, within limits. Under the 2021 IRC, a beam can run past its end post up to one-fourth of its actual span (R507.5), and joists can cantilever past a beam by the amounts in Table R507.6, which sets the limit by joist size, species and back span. A cantilever toward the house lets the inner beam sit out of the foundation backfill.

Sources: 2021 IRC Section R507, decks; AWC DCA 6, prescriptive residential wood deck construction guide; 811 Before You Dig.

Groundwork Design Co. · designed by builders

Get your deck framing drawn before you dig

Add our deck framing sheet (+$350) to a design package: beam lines, piers, joist size, spacing and direction, connectors, stairs and rails, drawn to scale as a starting point your builder and building department confirm. Designed remotely from photos and measurements, anywhere in the U.S., from $349.

See design packagesSee sample plans

Building in central Pennsylvania? Our crews build this work around Lock Haven, Williamsport and State College, talk to our crew about your deck.

Published by Muthler Landscaping & Construction, owned by Thayne Muthler (PA HIC #PA212584). How we research and check facts: editorial policy.